Our Services
Three services, three fixed prices. Nothing hidden, nothing open-ended.
A detailed look at what each service covers, how the work happens, and what it costs.
← Back to HomeHow we approach every job
Diagnose first
Before any fitting is touched, we identify the root cause and explain it in plain terms. If the scope exceeds what's expected, that's discussed before work begins.
Work carefully
Water is isolated before any joint is opened. Surfaces are protected. Fitting standards follow CNS specifications.
Test before leaving
Every job is pressure-tested and visually checked before we pack up. The work area is cleaned, and anything removed leaves with us.
Drip & Leak Repair
NT$3,800A careful check of taps, mixers, and joints to locate a leak and seal it cleanly where possible. Suits slow drips, damp cabinets, and taps that no longer close properly. The cause is explained before any work starts, and everything is tested watertight before the plumber leaves. A short note covers early signs to watch for in the same area.
What's included
- Inspection of taps, mixers, flexible hoses, and joint connections
- Replacement of faulty washers, cartridges, or O-rings (parts at cost)
- Under-sink and cabinet area check for secondary dampness
- Pressure check post-repair to confirm the seal
- Plain verbal summary of findings and any early warning signs
Typical process
Locate source: isolate water supply, inspect all fittings in the affected area
Explain finding and agree on the repair approach before starting
Replace or reseal the faulty component, restore water supply
Pressure test, check for residual damp, clean up work area
Drain Clearing & Trap Check
NT$8,000Clearing of blocked sinks, showers, baths, and toilets with a trap inspection to restore steady flow. Methods are chosen to suit the pipework at hand — mechanical rodding, manual trap removal, or camera-assisted locating for stubborn or deep blockages. Nearby fixtures are checked while on site, and straightforward upkeep advice is shared so the drain stays clear longer.
What's included
- Unblocking of sink, shower, bath, or toilet drain
- Trap removal, inspection, and clean or replacement
- Camera inspection for deep or repeat blockages (included)
- Check of adjacent fixtures for slow drainage
- Upkeep advice specific to the pipe type and layout
Typical process
Assess severity: test flow rate, inspect trap and visible pipework
Select clearing method to suit the blockage type and pipe material
Clear the blockage, clean the trap, check adjacent fixtures
Run water to confirm full flow, clean area, share maintenance tips
Installation & Whole-Home Review
NT$13,500Fitting of taps, valves, hoses, and traps, plus installation of a toilet, basin, shower, or water heater on request, with a full review of water pressure and pipe condition across the home. Scope is agreed before work starts, each item is demonstrated on completion, and a plain written summary is provided — useful for landlords and property managers.
What's included
- Fitting of taps, valves, hoses, traps, and flexible connections
- Toilet, basin, shower tray, or water heater installation (on request)
- Full home pressure check and pipe condition assessment
- Demonstration of each installed item
- Plain written summary of work and parts used
Typical process
Agree scope: review items to be fitted, confirm any special requirements
Home pressure and pipe check to flag any pre-existing conditions
Installation of agreed items using CNS-compliant parts
Pressure test, demonstration, written summary handover, clean-up
Which service fits your situation?
A quick comparison to help you decide before you get in touch.
| Situation | Drip & Leak NT$3,800 |
Drain Clearing NT$8,000 |
Installation NT$13,500 |
|---|---|---|---|
| Tap dripping or not closing fully | ✓ Best fit | — | — |
| Damp under the kitchen sink | ✓ Best fit | — | — |
| Sink or shower draining slowly | — | ✓ Best fit | — |
| Toilet or bath completely blocked | — | ✓ Best fit | — |
| Fitting a new tap or basin | — | — | ✓ Best fit |
| Water heater or toilet installation | — | — | ✓ Best fit |
| Moving into a new property, want a check | — | — | ✓ Best fit |
Not sure which applies? Describe the problem in the contact form and we'll advise before you commit.
Shared standards across all three services
Water isolated before opening
Supply isolation is done before any fitting is opened. Always.
CNS-compliant parts
All supplied fittings meet Chinese National Standards. Documented by batch.
Clean site on departure
Dust sheets laid, removed, and all debris taken from the property.
Pressure test before leaving
Every repair and installation is confirmed under working pressure before the plumber leaves.
Know which service you need? Let's get it sorted.
Use the contact form to describe the job. We'll confirm a slot — often same-day for morning enquiries.
Contact Us